Replacing the valve body on a Subaru Impreza 2.0i can be a complex task, but I’ll break it down into simpler steps for you. click here for more details on the download manual…..
- No-drill install: OEM Subaru Impreza Sport skirt moldings on base & Limited models 2017-2022 PLEASE NOTE* I had shown the wrong part number for the smaller Subaru fasteners in the video. Correct number is down below …
- 08-14 subaru Impreza, xv, and cross trek radiator replacement FB20 manual. subaru impreza radiator swap. easy and minimal tools needed. may differ with OEM air box. I do not have the OEM air box.
Before you start, make sure you have the necessary tools and parts, as well as a safe working environment. It’s also important to note that this is a general guide and you should consult a repair manual specific to your vehicle for detailed specifications and instructions.
### Tools and Materials Needed:
– Socket set and ratchet
– Wrench set
– Screwdrivers (flathead and Phillips)
– Pliers
– Torque wrench
– Replacement valve body (OEM part)
– New transmission fluid
– Gasket or sealant (if required)
– Clean rag or shop towel
– Safety glasses and gloves
### Steps to Replace the Valve Body:
1. **Preparation**:
– **Safety First**: Make sure the car is parked on a flat surface, and turn off the engine. Engage the parking brake.
– **Disconnect the Battery**: Disconnect the negative terminal of the battery to prevent any electrical issues.
2. **Remove the Transmission Pan**:
– **Drain the Transmission Fluid**: Place a drain pan underneath the transmission and remove the drain plug to let the fluid drain out. If there is no drain plug, you will need to remove the transmission pan.
– **Unbolt the Transmission Pan**: Use a socket wrench to remove the bolts securing the transmission pan. Carefully lower the pan, allowing any remaining fluid to drain out.
3. **Access the Valve Body**:
– **Remove the Filter (if applicable)**: If your model has a transmission filter, it will need to be removed. this may involve unbolting it or simply pulling it off.
– **Disconnect Electrical Connectors**: Locate and carefully unplug any electrical connectors attached to the valve body. Take note of where each connector goes for reassembly.
4. **Remove the Valve Body**:
– **Unbolt the Valve Body**: Use your ratchet and socket to remove the bolts holding the valve body in place. Make sure to keep track of the bolts and their locations.
– **Carefully Remove the Valve Body**: Once all bolts are removed, gently lift the valve body out. It may be slightly stuck due to old gasket material, so be careful not to damage any surrounding components.
5. **Install the New Valve Body**:
– **Prepare the New Valve Body**: If the new valve body requires a gasket, ensure it is properly aligned. If using sealant, apply it according to the manufacturer’s instructions.
– **Position the New Valve Body**: Carefully place the new valve body into the transmission, ensuring all passages align correctly.
– **Bolt it Down**: Reinstall the bolts and tighten them to the manufacturer’s specified torque settings using a torque wrench.
6. **Reassemble the Transmission**:
– **Reattach the Filter**: If you removed a filter, reinstall it according to the manufacturer’s specifications.
– **Reinstall the Transmission Pan**: Clean the pan and the mating surface on the transmission. Then, reinstall the transmission pan
and secure it with the bolts.
– **Reconnect Electrical Connectors**: Plug in all electrical connectors that were disconnected earlier.
7. **Refill Transmission Fluid**:
– **Add New Fluid**: Using a funnel, pour the appropriate type and amount of transmission fluid into the dipstick tube according to the manufacturer’s specifications. (Refer to the owner’s manual for the correct fluid type and capacity.)
8. **Reconnect the Battery**:
– Reconnect the negative terminal of the battery.
9. **Test Drive**:
– Start the engine and let it warm up. Check for any leaks under the vehicle.
– With the engine running, shift through all the gears to ensure smooth operation.
– Take the car for a short test drive to ensure everything is functioning properly.
### Final Checks:
– After your test drive, double-check the fluid level and add more if necessary. Look under the car for any signs of leaks and ensure that all electrical connections are secure.
### Important Notes:
– If at any point you feel uncomfortable or unsure, it’s best to consult a professional mechanic.
– Always refer to the specific service manual for your Subaru Impreza 2.0i for detailed instructions and torque specifications.
By following these steps carefully, you should be able to replace the valve body in your Subaru Impreza 2.0i. Good luck!
An expansion tank, also known as a coolant reservoir or overflow tank, is a crucial component in a vehicle’s cooling system. Its primary function is to manage the coolant fluid as it expands and contracts with temperature changes during engine operation. When the engine heats up, the coolant expands, increasing in volume. The expansion tank provides a designated space for this excess coolant to flow, preventing pressure build-up that could damage the cooling system or lead to leaks.
Typically made from durable plastic materials, the expansion tank is connected to the radiator and the engine via hoses. It is designed with a cap that can withstand pressure, ensuring that the system remains sealed under high temperatures. The tank often features a minimum and maximum level indicator, allowing vehicle owners to easily check coolant levels and maintain optimal performance.
In addition to its primary function of accommodating expanded coolant, the expansion tank also plays a role in the system’s overall efficiency. It allows for the recovery of coolant as the engine cools down and the fluid contracts, drawing it back into the cooling system. this helps maintain the correct coolant level and aids in preventing overheating. Regular inspection of the expansion tank for cracks or leaks is essential for the vehicle’s reliability and longevity, as failure of this component can lead to severe engine damage.